Skip to content
Go Practicals Logo

Go Practicals

Now always complete your College Practical File on time and get the best grades.

Menu

  • Home
  • Subject
    • 1st Year
    • Chemical/Petroleum
    • Computer Science
    • Civil
    • Electrical
    • Mechanical
    • Electronics & Communication
  • Contact Us
  • Submit
  • Team

Author: GP Team

PLUMBING SHOP : Introduction, Tools and Joints – Workshop Practical

plumbing-workshop-practical

The Plumbing Shop maintains all plumbing fixtures in restrooms, labs, and kitchen areas. The Plumbing Shop maintains pipe systems for domestic water, sanitary sewage, heating, and cooling supply lines, high-pressure airlines, vacuum lines, natural gas lines, and other pipes as

GP Team May 9, 2020May 9, 2020 Workshop No Comments Read more

Determination of Coefficient of discharge for Venturimeter – Fluid Practicals

Determination of Coefficient of discharge for Venturimeter – Fluid Practicals

A venturimeter is a device used for measuring the rate of a flow of a fluid flowing through a pipe. It consists of three parts. A short converging part: It is that portion of the venturi where the fluid gets converges.

GP Team December 17, 2017December 17, 2017 Fluid Mechanics 1 Comment Read more

Verification of Bernoulli’s equation using Venturimeter – Fluid Practicals

bernauli venturimeter

The Bernoulli Equation can be considered to be a statement of the conservation of energy principle appropriate for flowing fluids. The qualitative behavior that is usually labeled with the term “Bernoulli effect” is the lowering of fluid pressure in regions

GP Team December 17, 2017December 17, 2017 Fluid Mechanics No Comments Read more

To calibrate the given Rectangular Notch – Fluid Practicals

rectangular notch

A Notch is regarded as an orifice with water level below its upper edge. Notch is made of a metallic plate and its use is to measure the discharge of liquids. These are used for measuring the flow of water

GP Team December 17, 2017December 17, 2017 Fluid Mechanics 1 Comment Read more

Determination of Coefficient of discharge for Orifice Meter – Fluid Practicals

Orifice flow experiment

An orifice meter is a conduit and a restriction to create a pressure drop. An hour glass is a form of orifice. A nozzle, venturi or thin sharp edged orifice can be used as the flow restriction. In order to

GP Team December 17, 2017December 17, 2017 Fluid Mechanics No Comments Read more

To calibrate the given Trapezoidal Notch – Fluid Practical

trapezoidal notch

A Notch is regarded as an orifice with water level below its upper edge. Notch is made of a metallic plate and its use is to measure the discharge of liquids. These are used for measuring the flow of water

GP Team December 17, 2017December 17, 2017 Fluid Mechanics No Comments Read more

To calibrate the given V-notch – Fluid Practicals

v notch experiment

A Notch is regarded as an orifice with water level below its upper edge. Notch is made of a metallic plate and its use is to measure the discharge of liquids. These are used for measuring the flow of water

GP Team December 17, 2017December 17, 2017 Fluid Mechanics 1 Comment Read more

To study op-amp as inverting and non-inverting amplifier – AIC Practical

inverter

An operational amplifier (often op-amp or opamp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op-amp produces an output potential (relative to circuit ground) that is typically hundreds of

GP Team November 5, 2016November 5, 2016 Analog Integrated Circuits No Comments Read more

To study half wave rectifier of Single Phase Supply – AIC Practical

halfwave-rectifier

In half-wave rectification of a single-phase supply, either the positive or negative half of the AC wave is passed, while the other half is blocked. Because only one half of the input waveform reaches the output, mean voltage is lower.

GP Team November 5, 2016November 5, 2016 Analog Integrated Circuits No Comments Read more

To study the Schmitt trigger characteristic using IC 741 – AIC Practical

Schmitt-Trigger

In electronics, a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the non-inverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital

GP Team November 5, 2016November 5, 2016 Analog Integrated Circuits No Comments Read more
  • « Previous

Search

Recent Practicals

  • Estimation of Alkalinity of Water by Titrating it against standard Sulphuric Acid solution – Chemical Practical
  • Determination of Temporary Hardness of water sample by O’ Henner’s method – Chemical Practical
  • Proximate Analysis of Solid Fuels – Chemical Practical
  • To Determine total hardness of Water sample in terms of Caco3 by EDTA Titration method using Eriochrome black T indicator – Chemical Practical
  • PAINTING SHOP : Introduction, Tools and Precautions – Workshop Practical

Branches

  • Analog Integrated Circuits
  • Basic Chemical
  • Basic Computers
  • Basic Electrical
  • Basic Electronics
  • Basic Mechanical
  • Concrete Technology
  • Fluid Mechanics
  • Hydraulics & Hydraulic Machines
  • Physics
  • Workshop

Recent Comments

  • Indraj Kumar on FITTING SHOP ( Make a Joint) , Parts, Accessories, Diagram And Explanation – Workshop Practical
  • Sumit Kumar on To find the Overall Efficiency of a Centrifugal Pump – Hydraulics Practical
  • Abhishek on FOUNDRY SHOP : Introduction, Tools and Precautions – Workshop Practical
  • Sirhid on Determination of Metacentric Height Experimentally- Fluid Practicals
  • Sirhid on Determination of Metacentric Height Experimentally- Fluid Practicals

Contact Information

  • Go Practicals Team
  • Email: contact@gopracticals.com
  • Website: www.gopracticals.com

Search For Practicals

Recent Posts

  • Estimation of Alkalinity of Water by Titrating it against standard Sulphuric Acid solution – Chemical Practical
  • Determination of Temporary Hardness of water sample by O’ Henner’s method – Chemical Practical
  • Proximate Analysis of Solid Fuels – Chemical Practical
  • To Determine total hardness of Water sample in terms of Caco3 by EDTA Titration method using Eriochrome black T indicator – Chemical Practical
  • PAINTING SHOP : Introduction, Tools and Precautions – Workshop Practical

Subjects

  • Analog Integrated Circuits
  • Basic Chemical
  • Basic Computers
  • Basic Electrical
  • Basic Electronics
  • Basic Mechanical
  • Concrete Technology
  • Fluid Mechanics
  • Hydraulics & Hydraulic Machines
  • Physics
  • Workshop

Important Links

  • Home
  • Meet The Team
  • Join/Contribute
  • Contact Us
  • Submit Practicals
Copyright © 2025 Go Practicals. All rights reserved. Theme Spacious by ThemeGrill. Powered by: WordPress.